Photo Gallery

Pipe & Round Tube Bending

WeeBee's Restaurant in Montana 12" OD x .250" wall bent on an ellipse W12 x 22# bent the hard-way to a 23 ft radius All architecturally exposed.
Tanner Springs Park-Rainwater Pavillion in Portland, OR.. 4" Sch40 and 6" Sch40 bent by Albina Pipe Bending Co., Inc.
Clarity Sculpture at the University of La Verne, California 1-1/2" SCH40 BARE- bent to a complex configuration and then fit together.
Lightpost Sculpture Bent by Albina Pipe Bending Co., Inc.
Sun Valley Music Pavillion in Sun Valley, ID. 220,000# of pipe rolled ranging from 10" Sch80 to 10" XXH
10" and 12" Sch40 pipe bends
1-1/8" OD x .120 wall DOM Bends for an exercise equipment manufacturer
Various U-Tube Bends out of .748" OD x .063" wall TiGr2 1150 lengths x 240"-295" long 3" c-c diameter to 35" c-c diameter
122,000# of various structural steel including 12" extra heavy pipe and 8" Sch40 pipe at a 286 ft. outside radius. Various tube steel (including 7" x 4" x .313" wall) and wide flange (including W30 x 132# and W30 x 99# at a 231 ft. outside radius) were al
Wave Rack 180 Degree Bends
Custom Wave Rack
2½" Sch40 pipe A53B, bent as 180° sections 985 lengths x 21 ft. 6" CLR
1" OD x .065" wall 304 Stainless Steel Polished ID/OD. Fabricated Complete
1" OD x .065" wall 304 Stainless Steel Polished ID/OD. Fabricated Complete
14" Sch80 pipe on an elliptical curve (ranging from 8' 0" radius to a 20' 0" radius). End of the Oregon Trial Museum Located in Oregon City, Oregon
Sun Valley Music Pavillion in Sun Valley, ID. 220,000# of pipe rolled ranging from 10" Sch80 to 10" XXH
14" OD x .437" wall bent to a 33' 0" Radius
10" Sch60, Bent Canopy Located in Portland, Oregon at the Clackamas Town Center
1-3/4" and 2" Solid Round- custom parts bent for defense projects
2" Sch40 18" to 24" offsets bent by Albina Pipe
4” and 5” pipe spools with wear backs, bent and fabricated by our local 290 Steamfitters
3-1/2” Sch40 ballards for a gas station to protect the gas pumps
14" Pipe Truss at the Portland, Oregon Convention Center
6" Sch40 Blk and 6" Sch40 T304 S/S bent to a 36" CLR
256 Spiral Coils from 3/4" OD x .059" wall SA213, T316H
16" and 8" pipe bent cold at Albina Pipe Bending, Co., Inc. Canopy section at the Portland Oregon Airport Fabrication by Fought & Company
1-1/2" Sch40 and 1-12" Sch80 6061-T6 Aluminum to a 7'-103/4" CLR
14" Pipe Truss at the Portland, Oregon Convention Center
920 pcs of: TS 1 x 1" x .120" wall tubing
5/8" OD x .150" wall DOM- Custom Coil
1-1/2" Sch40 Bare
1" OD x .065" wall 304 Stainless Steel Polished ID/OD. Fabricated Complete
Complex Pipe Bend
Custom Coil
3/8" OD x .049" wall S/S 2-3/4" c-c loops x 10-1/2" tall
1/2" OD x .049 wall 304 S/S 3" c-c diameter
10" Sch40 and 10" Sch80 Roof Truss at an Aquatic park in Glendale, CA. Bending by Albina Pipe Bending Co., Inc. Fabrication by Roscoe Steel and Culvert Co.
1/4" OD x .042" wall brass tubing
1/2" solid round 1018 CR
3/8" OD x .065" wall S/S 1" c-c to 5-3/4" c-c loops 12" tall
10" OD x .375" wall and 12" OD x .375" wall aluminum fabricated complete by Albina Pipe Bending
4" Sch40 A53B bent 180° to a 12" Radius
3" Sch10 and 4" Sch40 304 s/s rolled to a 42.5" diameter
Spiral rail bent out of 1½" Sch40 and 1/2" solid round. Spiral bent to a 21" plan view diameter
Customer coils with terminals bent out of 3/4" OD x .059" wall material
Stainless Steel Boiler Tubes
Entry Canopy
16" and 8" pipe bent cold at Albina Pipe Bending, Co., Inc. Canopy section at the Portland Oregon Airport Fabrication by Fought & Company
Canopy
Hanging Pancake Coil
Store Front for the Bedroom Super Store in Portland, OR.
6" Sch80 pipe rolled into a "pringle shape"
1-1/2" Sch80 Pancake coils (various radii)
2-1/2" Sch40 6063-T6 Aluminum bent to a 12" radius
2-1/2" Sch40 6063-T6 Aluminum bent to a 12" radius
2" Sch10 s/s Steam coils
18" OD Round Tubing A bridge in downtown Portland, Oregon
2 lengths x 39 ft. of 24" OD x 1" wall pipe 46' 0" outside radius bent within PFI standards St. Mary's Center for Health Reno, NV. Material supplier PDM Steel in Sparks, NV.
24” OD x 1” wall pipe 46’ 0” Outside Radius Bent within PFI standards
10" Sch40 pipe offset
Portland International Airport Headquarters and Parking Garage 3-1/2" Sch40 bent to a 12" CLR, 5" Sch40 bent to a 15" CLR and 6" Sch40 bent to a 24" CLR. All to various configurations and degrees.
Robson Square Ice Rink Vancouver, BC. 12 lengths (26,000#) of 12 3/4" OD X .500 " wall polished S/S. Bent to 38' CLR and 19' CLR
Sherwood High School Commons area custom bike rack
"Clarity" Sculpture at the University of La Verne, California 1-1/2" SCH40 BARE- bent to a complex configuration and then fit together.
108 pieces of 8-5/8" OD x .625" wall bent to a 24" CLR
Playground equipment at the Evergreen Space Museum in McMinnville, Oregon. 4" Sch40 ellipse bends by Albina Pipe Bending, all other components designed and fabricated by Columbia Cascade Company.
MET Bus Sign in Billings, Montana 3-1/2" Sch40 Aluminum, 180 degree bend and a 24" CLR. Bent by Albina Pipe Bending Co., Inc.
Custom Handrails
Custom Handrails
Museum of Flight, Seattle, WA. 128,894# of 5" Sch120 and 5" Sch40 pipe rolled. All material Architecturally Exposed.
8" Sch20 T304 S/S Material Rolled to a 47" IR All materials rolled to PFI standards
The Group Health Headquarters Seattle, WA. 6" Sch40 pipe bent to a 5'3" OR 8" XXH pipe bent to a 18' 4" IR 10" Sch40 pipe bent to a 13' 3' IR
The Group Health Headquarters Seattle, WA. 6" Sch40 pipe bent to a 5'3" OR 8" XXH pipe bent to a 18' 4" IR 10" Sch40 pipe bent to a 13' 3' IR
Fabricatrion of bollars forming special aluminum sleeves with 18' beam DIA made of 3/4" thick wall aluminum pipe.
12-3/4" OD x .500" wall SA106B SMLS bent to a 5'0" CLR
150 pcs.: 3" Sch80 Mild Steel bent to a 10" CLR
Museum of Flight, Seattle, WA. 128,894# of 5" Sch120 and 5" Sch40 pipe rolled. All material Architecturally Exposed.
Museum of Flight, Seattle, WA. 128,894# of 5" Sch120 and 5" Sch40 pipe rolled. All material Architecturally Exposed.
Sun Valley Music Pavillion in Sun Valley, ID. 220,000# of pipe rolled ranging from 10" Sch80 to 10" XXH
20" OD x .750" wall material bent to a 23' 0" CLR
10" Sch40 pipe Rolled to a 2' 6" CLR to PFI standards